RAD-Moon 3
2.5/5/10GBASE-T1 MultiGigabit Media Converter for Automotive Ethernet2.5/5/10GBASE-T1 MultiGigabit Media Converter for Automotive Ethernet
Intrepid’s MultiGigabit Media Converter RAD-Moon 3 is the latest Ethernet Media Converter for 2.5/5/10GBASE-T1 MultiGigabit Automotive Ethernet applications. The RAD-Moon 3 converts the Ethernet physical layer from MultiGBASE-T1 to MultiGBASE-T. This is needed to directly connect a PC equipped with the standard 8-wire Ethernet to an automo tiveECU or Switch which use the 2-wire version of Ethernet specific to In-Vehicle Networks. (IVNs)
Key Features
- 2.5/5/10GBASE-T1 (10GBASE-T1 support is not fully validated on revision 1 hardware) physical layer using the Marvell 88Q4364 PHY**
- Intuitive LED indicators
- PHY configuration, link status, and
network activity - Bar graph display of MultiGBASE-T1 Signal Quality Indicator (SQI) in real-time
- PHY configuration, link status, and
- Membrane buttons allowing device configuration without software
- Switch between 2.5G, 5G, and 10G link speeds
- Select the MultiGBASE-T1 PHY clock configuration
- Uses the H-MTD connection system designed for MultiGBASE-T1
- 6-40V power range, compatible with in-vehicle power from barrel jack.
- Ruggedized USB Type-C connector for device configuration and firmware updates
- PHY register monitoring and updating over USB using Vehicle Spy or Intrepid’s Open Source API
The RAD-Moon 3 provides a small but rugged enclosure perfect for carrying in your laptop bag.
Using the RAD-Moon 3 as a 2.5GBASE-T1 to 2.5GBASE-T converter or 5GBASE-T1 to 5GBASE-T converter or 10GBASE-T1 to 10GBASE-T converter.
Connecting a PC directly to an automotive ECU using the RAD-Moon 3 is useful for simulating other vehicle nodes, performing direct diagnostics, or ECU reflashing.
The registers of the MultiGBASE-T1 PHY can be accessed for direct control and monitoring of its operation, as well as enable test and diagnostic modes.*
ORDERING INFORMATION:
| Part Number | Description |
| RAD-Moon 3 | 2.5/5/10GBASE-T1 Media Converter for Automotive Ethernet |
Specifications subject to change; please contact Intrepid for the latest information. All trademarks are the property of their respective owners.
*88Q4364 register information must be acquired under NDA directly from Marvell Semiconductor.
**1000BASE-T1 is not supported by the 88Q4364 and 10GBASE-T1 support is not fully validated on revision 1 hardware
Media Converter Comparison Chart
| RAD-Moon 3 | RAD-Moon 2 | RAD-Comet 2 | RAD-Meteor | RAD-Moon | |
| 2.5/5/10GBASE-T1 "Multi-Gig" Media Converter for Automotive Ethernet | 100/1000BASE-T1 Media Converter for Automotive Ethernet | 10BASE-T1S Development Interface with 100BASE-T1, 10/100/1000BASE-T, and CAN FD | Low Cost Device for Interacting with 10BASE-T1S Networks | 100BASE-T1 Ethernet Media Converter | |
| PHY | Marvell (88Q4364) | Marvell (88Q2220M) | Microchip (LAN8671) and Marvell (88Q2221M) | Microchip LAN867X | NXP (TJA1100) |
| Connector | H-MTD | H-MTD | Industrial connector and H-MTD | Terminal Block | Molex Mini50 |
| Voltage Input | 6-40V | 4.5-40V | 5.5V-40V | 125mA at 5 V (bus load 1%), 140 mA at 5V (Test Mode 1) | 250 mA @ 5V or about 1.25W |
| Power | Barrel Jack | Ruggedized USB Type-C or Barrel Jack | Ruggedized USB Type-C or Barrel Jack | USB Type-C | Mini-USB |
| Configure | Ruggedized USB Type-C connector for device configuration and firmware updates | Ruggedized USB Type-C for configuration and PHY register monitoring | Ruggedized USB Type-C connector for device configuration and firmware updates | USB Type-C | Mini-USB |
| TC10 | Yes | Yes | Yes | No | No |
| MACsec | No | Yes | Yes | No | Yes |
| Barrel Jack | Yes | Yes | Yes | No | No |
| Programmable membrane label with LEDs | Yes | Yes | Yes | No - Display | No |
| Vehicle Spy 3 Support | Yes | Yes | Yes | No | No |
| Learn More >> | Learn More >> | Learn More >> | Learn More >> | Learn More >> |
Related Posts
Introduction to 10GBASE-T1 Multigigabit “Multi-Gig” for Automotive Ethernet
The automotive industry is rapidly evolving, and with the advent of new technologies, the demand for high-speed and reliable connectivity within vehicles has increased. In order to meet these requirements, a new standard known as 10GBASE-T1 Multigigabit "Multi-Gig"...
Everything you need to know about Automotive Multi-Gig Ethernet
Discover why OEMs are asking for Multi-Gig Ethernet tools in the next generation of vehicle network architecture.
2.5/5/10GBASE-T1 Media Converter for Automotive Ethernet Demo at Automotive Testing Expo Novi 2022
Introducing 2.5/5/10GBASE-T1 "Multi-Gig" Media Converter for Automotive Ethernet at Automotive Testing Expo Novi.
