1-800-859-6265

neoVI FIRE: 6x CAN, 4x LIN / neoVI RED: 2x CAN, 2x LIN

Home » Products » Vehicle Network Adapters » Private: neoVI FIRE/RED » neoVI FIRE/RED Specifications

Overview

Specifications

neoVI FIRE Brochure (PDF)

neoVI RED Brochure (PDF)

User’s Guide

Buy the neoVI FIRE

Buy the neoVI RED

General Specifications

  • neoVI 3G Architecture: enhanced performance over previous devices
  • 3 DSPs and 1 RISC processor for 125 MIPS of processing capacity
  • Power consumption (typical): 150mA @ 14.4 VDC
  • Sleep power consumption (typical): 12mA @ 12.0 VDC
  • Power supply: 5.5-27V operation
  • Temperature range: -40°C to +85°C
  • Vehicle connectors: male DB-25 and male DB-9
  • Warranty: One year limited
  • Firmware: Field upgradeable flash design
  • General purpose I/O: 6 MISC I/O channels (0-5V on MISC I/O 1-2 and 0-3.3V on MISC I/O 3-6); 4 I/O can be configured as analog
  • General Purpose I/O rate report interval: 1 Hz to 10 kHz or based on digital change
  • General Purpose I/O maximum current output (sunk/sourced): 4 mA
  • Microsoft-certified USB drivers
  • Isolated USB
  • Standalone mode including scripting, receive messages, transmit Messages, expressions, I/O, and transport layers
  • ICS TimeSync for multiple hardware synchronization, supporting all neoVI 3G devices
  • neoVI FIRE: J2534 and RP1210 A/B compatible for CAN/ISO15765, Keyword, and ISO9141
  • neoVI RED: J2534 and RP1210 A/B compatible for CAN/ISO15765, Keyword, and ISO9141
  • microSD card slot support for cards up to 2 GB in size, formatted using FAT32 for direct use in a PC
  • Battery-backed real time clock (RTC)

Timing Specifications

  • 64-bit timestamping to accuracy of 10 microseconds on CAN and LIN networks with no overflow; 0.5 microsecond accuracy timestamp available if using only one network
  • Simultaneous operations on all CAN/LIN networks
  • Transmit message double-buffering on all networks allows back to back message transmission

neoVI FIRE Network Specifications

CAN

  • 6x CAN channels
  • 4 Dedicated ISO11898 Dual Wire CAN Physical Layer (TJA1040)
  • 1 Dedicated ISO11519 Low Speed Fault Tolerant CAN Physical Layer (TJA1054A)
  • 1 Dedicated Single Wire CAN Physical Layer GMW3089 / SAE J2411 (MC33897)
  • CAN 2.0B Active
  • Up to 1 Mb/s software-selectable baud rate (auto baud capable)
  • Capable of generating and detecting error frames
  • Logic analysis of CAN waveform with 25 ns resolution
  • Graphical bit time / baud rate calculator
  • Listen only mode support
  • Unterminated network detection
  • High speed mode, test tool resistor, and high voltage wakeup support

LIN / ISO9141 / Keyword 2000 / K and L Line

  • 4x LIN (Local Interconnect), ISO9141, Keyword 2000, or K and L Line
  • Full support for LIN 1.X, 2.X and J2602
  • LIN J2602 / 2.X compatible physical layer
  • Software-selectable LIN master resistor
  • Capable of generating LIN waveforms (Including errors) using dedicated output compare hardware
  • UART-based state machine
  • Initialization waveforms including Fast Init, Five Baud, and Custom
  • Programmable timing parameters including Inter-Byte, TX Inter-Frame, RX Inter-Frame and Initialization Waveforms (0.5 ms Resolution)
  • Software-selectable baud rate
  • LIN Bus Monitor Mode identifies errors: Sync Break Error State and Length, Sync Wave Error, Message ID Parity, TFrameMax/Slave Not Responding, Checksum Error and Transmit Bit Errors
  • LIN Bus Master Mode operates at same time as LIN Bus Monitor
  • LIN Bus Slave simulation, with or without an LDF file
  • LIN Bus hardware schedule table with support for LIN diagnostics

GM CGI

  • 1x GM CGI
  • Software-enabled (disables LIN2)
  • Programmable bit rate
  • Full block mode message reception only

neoVI RED Network Specifications

CAN

  • 2x CAN channels
  • 1 Dedicated ISO11898 Dual Wire CAN Physical Layer (TJA1040)
  • 1 User Selectable ISO11898 Dual Wire CAN Physical Layer (TJA1040), SO11519 Low Speed Fault Tolerant CAN Physical Layer (TJA1054A), or Single Wire CAN Physical Layer GMW3089 / SAE J2411 (MC33897)
  • CAN 2.0B Active
  • Up to 1 Mb/s software-selectable baud rate (auto baud capable)
  • Capable of generating and detecting error frames
  • Logic analysis of CAN waveform with 25 ns resolution
  • Graphical bit time / baud rate calculator
  • Listen only mode support
  • Unterminated network detection
  • High speed mode, test tool resistor, and high voltage wakeup support

LIN / ISO9141 / Keyword 2000 / K and L Line

  • 2x LIN (Local Interconnect), ISO9141, Keyword 2000, or K and L Line
  • Full support for LIN 1.X, 2.X and J2602
  • LIN J2602 / 2.X compatible physical layer
  • Software-selectable LIN master resistor
  • Capable of generating LIN waveforms (Including errors) using dedicated output compare hardware
  • UART-based state machine
  • Initialization waveforms including Fast Init, Five Baud, and Custom
  • Programmable timing parameters including Inter-Byte, TX Inter-Frame, RX Inter-Frame and Initialization Waveforms (0.5 ms Resolution)
  • Software-selectable baud rate
  • LIN Bus Monitor Mode identifies errors: Sync Break Error State and Length, Sync Wave Error, Message ID parity, TFrameMax/Slave Not Responding, Checksum Error and Transmit Bit Errors.
  • LIN Bus Master Mode operates at same time as LIN Bus Monitor
  • LIN Bus Slave simulation, with or without an LDF file
  • LIN Bus hardware schedule table with support for LIN diagnostics

* Specifications subject to change. Please contact Intrepid for the latest information.

JapanKoreaChinaUSA